Search for product

Hotline / Order

Tel.: +49 (0)3585 / 470 222
Fax: +49 (0)3585 / 470 213

myAVR Board light PLUS, assembly kit

Product groups > Top Sellers > myAVR Board light PLUS, assembly kit


myAVR Board light and myAVR LCD add-on for text:
soldering ... programming ... testing

This combined kit consists of the board myAVR Board light and the myAVR LCD Add-On. It is recommended for learners who like to build the hardware themselves for their experiments.
The myAVR Board light is a development board to learn the programming of microcontrollers. The programming of the controller and the communication with PC are realized by the USB interface.
The myAVR Board light is the low cost version for scholars, students and trainees. It is without the comfort like the boards of MK2 or MK3. Regardless it contains all the necessary components needed to learn microcontroller programming.
The myAVR LCD add-on expands the myAVR Board light with a text LCD. On this LCD texts can be displayed 2 lines, each with 16 characters.
 

Properties

    myAVR Board light, assembly kit
  • development board for ATMEL microcontrollers
  • mini USB interface
  • programming and comunication via USB
  • power supply via USB
  • programmable in Assembler, C/C++ and BASCOM
  • ISP interface optional
  • Easy to handle, special cables not nessecary
  • Expansion socket for additional add-ons
    myAVR LCD add-on, assembly kit
  • High-quality LC display(2 lines, 16 characters for each line)
  • operating voltage: typical 4.8 - 5.3 V
  • Background illumination:
    • can be switched via jumper
    • regulated via the microcoller program
 

Equipment

    myAVR Board light, assembly kit
  • mini USB interface via myUSBtoUART
  • ATmega8A   with preinstalled myAVR bootloader (myAVR ProgTool)
    → properties of the ATmega8  [show/hide]
  • Input and output devices:
    • 3 miniature switches
    • 2 potentiometer
    • 1 analogue photo sensor
    • 1 Buzzer (frequency converter)
    • 3 LEDs (red, green, yellow)
  • grid 2.54 mm (0.1 inch)
    myAVR LCD Add-On, assembly kit
  • LCD for text with 2 lines each for 16 characters
  • with background illumination
  • with contrast control
  • Jumper for setting the R/W signal
  • with connections for myAVR boards as well as for further add-ons
 
Driver are available for
  • Windows CE, Windows 2000 / 2003 / XP / Vista / 7 / 8 / 10
  • Linux
  • MacIntosh OSX
=> You can download the driver for this systems at www.silabs.com
=> You can find the USB driver for myAVR products with Windows in the myavr download


 

 

Supported controlers

  • ATmega8/48/88/168/328
  • ATtiny48/88

Bootloader

  • You can find bootloader for Windows in our Download-area (search "DL120" or "bootloader")
    for different controllers
  • You can find bootloader for LINUX in our Download-Area (search "DL233" or "LINUX")
Please note:
The controller included in this kit is supplied with bootloader, default for use with windows operating system.
When you purchase an additional controller for this board, we recommend you to order it with a bootloader. Please mention this in your online order in the comments field.

Scope of supply:

myAVR Board light, assembly kit
  • 1 microcontroler ATmega8
    with pre-installed bootloader for Windows
  • 1 USB-2-UART-bridge with mini USB connection
  • 1 green LED 2 mA
  • 1 yellow LED 2 mA
  • 1 red LED 2 mA
  • 3 capacitor 100 nF
  • 2 capacitor 22 nF
  • 3 resistor 1.2 kΩ
  • 1 resistor 10 kΩ
  • 1 photo sensor
  • 1 inductor 10 μH
  • 1 quartz 3.6864 MHz
  • 2 potentiometer
  • 2 shaft for potentiometer
  • 2 miniature button 9.5 mm
  • 1 miniature button 4.3 mm
  • 1 buzzer
  • 1 female connector
  • 4 feets for the board
  • 1 circuit board
  • multi-colored patch cables
myAVR LCD add-on, assembly kit
  • 1 circuit board
  • 1 LCD modul with 2 lines and each 16 characters
  • 1 female connector, 20 pole
  • 1 multi-pin connector, 20 pole
  • 1 multi-pin connector, 16 pole
  • 2 multi-pin connector, 3 pole
  • 1 potentiometer (for contrast)
  • 1 resistor 1.2 kΩ
  • 1 resistor 10.5 kΩ
  • 1 transistor (regulation for illumination via PWM)
  • 2 jumper
  • 4 feets for the board
myavr_board_light_plus_bausatz.png

Example of use:
myAVR Board light with
myAVR LCD Add-On

Recommended articles (not included)


Also order!

The myAVR Solder set . The perfect basic equipment for all hobbyist and people who solder!

myAVR Solder set


myAVR Board light PLUS, assembly kit
reasonably priced!
learn and experimenting board to equip and solder by yourself, and also the assembly kit for the myAVR LCD Add-On
  • connection via mini-USB, optional via ISP
  • ATmega8
  • In- and output devices
  • grid: 2.54mm
  • LC-display with 2x16 characters
  • background illumination
  • contrast control
list price: 29.95 Euro
 

We recommend the following articles:

cable mini USB

ISP Connect Kit 10/6 pole

IC-Sockel 28

Pin connector 6pole

Skirting board SPL8, single-row

myAVR Solder set

GraficLCD Add-On, assembly kit

Our regional partners

Business partner wanted!

To expand our sales area we are looking for partners to represent our products and interests of the Laser & Co. Solutions GmbH.

myAVR Board MK3

Develop games with

mySmartUSB MK2

For professionals

Shop  •  Download  •  Shop-infos  •  Quality  •  Customers worldwide  •  Privacy  •  Shipping and payment  •  Contact

Copyright © Laser & Co. Solutions GmbH, 2009-2015