Search for product

Hotline / Order

Tel.: +49 (0)3585 / 470 222
Fax: +49 (0)3585 / 470 213

mySmartUSB MK3 (programmer and bridge)

Product groups > systemboards and programmer > mySmartUSB MK3 (programmer and bridge)


mySmartUSB MK3

compact and powerfull high-speed USB programmer and communication interface
for Atmel AVR microcontroller

mySmartUSB MK3 is a compact high-speed USB programmer, designed in SMD construction and as a daugther board. So it is possible to programm a large number of AVR systems via the USB interface with this board. JTAG interface and ISP interface expand the application possibilities.
The communication interface can be used as UART, TWI/I²C or SPI-Bridge. The communication with a PC works completly transparent via a virtual COM port. The board will be connected via USB interface with the PC and supplied with power. A large number of AVR systems can be programmed with this board via the USB interface and communicate with a system via an UART-USB bridge.
With the preinstalled bootloader it is possible to update the firmware for new types of controller and protocols. In addition, mySmartUSB MK3 can be used as a basis for further applications, for example for a UART-USB, SPI-USB, TWI-USB converter.
 
Overview



For a bigger sight click on the picture!

programming



For a bigger sight click on the picture!

communication


For a bigger sight click on the picture!

 

Properties:

  • compact and powerful high-speed USB programmer and communication interface for Atmel microcontroller
  • power supply via USB connection
  • 3 V und 5 V option
  • simple programming via USB interface from variety of AVR-systems
  • easy communication via USB - possible over UART, TWI (I²C) or SPI
  • firmware update by preinstalled bootloader possible
  • switchable between programming, communication rest mode and myMode
  • programming mode:
    • ISP
    • highvoltage parallel
    • highvoltage serial
    • TPI
    • TPI highvoltage
  • selection of operating modes via software commands or mode buttons
  • additional function:
    • turning on and off the board voltage
    • reset of the programmer or target environment
    • retrieve current status information
    • can also be used with myAVR Board MK2

Equipment:

  • SMD construction
  • USB connection
  • ISP port
  • JTAG port
  • industriall standard USB controller (CP2102)
  • status LEDs
  • DIP switches
  • quartz 8 MHz
  • mode button
  • construction as daughter board, it can be used individually, e.g. for
    • programming other AVR systems with ISP connection
    • possible realization of highvoltage parallel interface
    • possible realization of highvoltage serial interface
    • USB-TWI / I²C bridge
    • etc.
  • dimensions: 60 x 30 x 15 mm
  • grind: 2.54 mm
Driver are available for
  • Windows CE, Windows 2000 / 2003 / XP / Vista / 7 / 8 / 10
  • Linux
  • MacIntosh OSX
=> You can download the driver for this systems at www.silabs.com
=> You can find the USB driver for myAVR products with Windows in the myavr download

System requirements for the mySmartUSB:
  • Hardware: USB 2.0 with standard USB A - connection
  • Cable: standard USB cable A-B
  • System software:
    Windows 2000 / XP / 2003 / Vista / 7 / 8 /10
    Mac OS9 / OSX
    Linux 2.4 / 2.6

Technical data

  • supply voltage: 5 V
  • operating current: 10 - 20 mA typical without other loads
    up to 100 mA if connected to target system
  • operating temperature: 0 -30 °C
  • supported protocols:
    • AVR109/910/911
    • STK500
  • supported programming methods:
    • ISP
    • highvoltage parallel
    • highvoltage serial
    • TPI
    • TPI highvoltage
  • selection supported controller families:   [show / hide]

Scope of supply:

  • USB-programmer
  • 10-pin flat cable with post connectors
  • 6-pin flat cable with post connectors
  • adapter board for the flat cables
  • 2 multi-pin connector2 (separately, not soldered on)
 
Note:
the mySmartUSB MK3 can programmed with following programming environments:
  • SiSy AVR (in German)
  • myAVR Workpad (in German)
  • AVR Studio
  • BASCOM AVR

 


mySmartUSB MK3 (programmer and bridge)
High-speed USB programmer and communication interface
  • to program AVR microcontroller,
  • supported several protocols, programming modi and interfaces like UART, TWI and SPI
list price: 38.00 Euro
 

We recommend the following articles:

myAVR Board MK3 256K PLUS    or
myAVR Board MK3 64K

myMultiProg MK3 PLUS, assembly kit

ISP Connect Kit 10 / 6 pole

USB cable

Our regional partners

Business partner wanted!

To expand our sales area we are looking for partners to represent our products and interests of the Laser & Co. Solutions GmbH.

STM32-Produktlinie

XMC product line

For beginners

Shop  •  Download  •  Shop-infos  •  Quality  •  Customers worldwide  •  Privacy  •  Shipping and payment  •  Contact

Copyright © Laser & Co. Solutions GmbH, 2009-2015