|
|
|
|
|
|
|
|
Hotline / Order
Tel.: +49 (0)3585 / 4702-22
Fax: +49 (0)3585 / 4702-13
|
|
|
|
myAVR Board MK2, assembly kit
Product groups >
hardware - assembly kits > myAVR Board MK2, assembly kit
available downloads for this product:
| |
|
The easy start in the world of mikrocontroller-programming
with the myAVR Board MK2!
|
The myAVR Board MK2 is a developer board for AVR-Controller-Programming. This board is for the beginner.
The connection between the board and a PC is possible via USB cabel. The programming and communication of
the Controller are realized by USB port. Input, output devices and ports are equipped with socket connectors.
It enables connections with Patch cables.
We develop a test program,
which includes many functions. It is necessary to connect the Input and output devices
with the ports of the myAVR Board MK2 like the description in the test program. With our german software SiSy AVR
as well as SiSy Microcontroller++ (Full Version or
Demo Version), you can burn this test program to the myAVR Board MK2.
Please notice that SiSy is a german development environment.
|
| |
Properties:
- board for education and individual experiments with ATMEL microcontrollers
- ATmega series (8/48/88/168/328)
- ATtiny series (48/88)
- USB port
- programming and communication via USB interface
- voltage supply via USB or extern
- integrated USB-Programmer mySmartUSB MK2
- Crystal with 3.6 MHz
- ATmega8A, properties
[show / shut down]
- 8 kByte Flash
- 512 Bytes EEPROM (100.000 write/read cycles)
- 1 kByte internal SRAM
- 2x 8 Bit Timer/Counter
- 1x 16 Bit Timer/Counter
- 6x analog-digital-converter channels
- Real Time Counter
- 23 digital in-, outputs
|
- ISP interface onboard
- infrared-interface optional
- easy handling, no special cables needed
- designed as IPO-model (input, process, output)
|
Equipment
- complete fitted myAVR Board MK2 with RISC AVR-microcontroller ATmega8
- ATmega8 with pre-installed test program
- integrated USB-Programmer mySmartUSB MK2
with communications interface
- Programmer and UART-Bridge
- ISP-Interface
- datatransmission by UART, TWI (I²C) or SPI without extern voltage supply
- updates via bootloader, e.g. for support new processors or commands
- with industry standard-controller (CP2102) USB to serial converter
- Power On and Power Off switchable by the user
- provided virtual COM-Port
- construction as daughter board, therefore individual applicable e.g. for
→ programming other AVR-systems with ISP-connection
→ realisation a USB-parallel-interface
→ realisation a USB-serial-interface (UART = COM = RS232)
→ USB-TWI / I²C-Bridge
→ etc.
- analog and digital in- and output devices, e.g.
- potentiometer
- button
- photosensor
- frequency converter
- LEDs
- highpos LED
- optional infrared-interface for receiver and transmitter
- socket connector for connect more Add-Ons
|
|
|
|
|
USB-Programmer mySmartUSB MK2
(integrated on myAVR Board MK2)
|
technical and mechanical data:
- supply voltage: 9 - 12 V
- operating current: 10-50 mA typical without more electronic user
- operating voltage: 3.3 - 5.3 V
- operating temperatur: 0 - 30 ° C
- dimensons: 90 x 90 x 18 mm
- grid dimension: 2.54 mm
|
supported controller series:
- ATmega8 / 48 / 88 / 168 / 328
- ATtiny48 / 88
|
| |
Scope of supply:
- 1 printed circuit board
- 1 Prozessor ATmega8
- 1 voltage regulator; µA 7806
- 1 rectifier; B80C800DIP
- 1 diode 1A 1N 4001
- 1 yellow LED 2 mA; LED 3MM 2MA GE
- 1 red LED 2 mA; LED 3MM 2MA RT
- 2 green LEDs 2 mA; LED 3MM 2MA GN
- 1 blue LED 2 mA; LED 3MM 2MA BL
- 2 capacitor 47 µF; ELKO RAD 47/25V
- 5 capacitor 100 nF; FOLIE MKS-2 100N
- 2 capacitor 22 pF; KERKO 22P
- 4 resistor 1,2 kΩ; METALL 1,20K
- 2 resistor 10 kΩ METALL 10K
- 1 resistor 160 Ω METALL 160R
- 1 photoconductive call, analoge; VT93N1
|
- 1 inductor 10 µH; SMCC 0,10µ
- 1 quartz 3,6864 MHz;3,686411-HC49U-S
- 2 potentiometer; RT 10-L 47K
- 2 rod for potentiometer
- 2 miniature switch; TASTER 3301B
- 1 IC-socket; GS 28
- 3 pin header male SPL 20
- 1 piezo electric buzzer; SUMMER EPM121
- 1 connector; PSS 254/2G
- 1 clutch empty case
- 2 crimp pin
- 1 pin header female; BL 1X20W 2,54
- 2 pin header female; BL 1X10W 2,54
- 2 multi-pin connector; SL 1X10W 2,54
- 4 feets for the board
- 1 mySmartUSB MK2 (programmer and bridge)
|
|
Notice:
the USB-Programmer mySmartUSB MK2 can used with these programming environment:
- SiSy AVR (in GERMAN!)
- SiSy Microcontroller++ (in GERMAN!)
- myAVR Workpad (in GERMAN!)
- BASCOM AVR
- Atmel Studio
|
|
The mySmartUSB Terminal
is free to download in our downloadarea for an easy application.
With this program are some functions realizable:
|
|
|
Now order!
The
myAVR Solder set
.
The complete basic equipment for soldering!
|
myAVR Board MK2, assembly kit
Developer board myAVR Board MK2 for ATMEL microcontroller
- as assembly kit
- programming via removeable daughterboard mySmartUSB MK2
- typical in- and output devices
- with photo sensor
- Infrared interface for receiver and transmitter
|
list price: 39.00 Euro
|
|
|
|
|
|
Business partner wanted!
To expand our sales area we are looking for partners to represent our products and interests of the
SiSy Solutions GmbH.
|
|
|
|
|
|
|
|
